These are the printed manuals for the ASR-X and ASR-X Pro. Syntaur is the exclusive producer and licensed distributor of Ensoniq’s manuals. ASR-X Reference. We cannot provide tech support for the general operation of your sampler; however, we do carry the manuals for the ASR-X and ASR-X Pro. Operating System. The ASR-X is a sampler, synthesizer, sequencer and effects studio workstation in a tabletop unit. It makes for a nice alternative to the Akai MPC (and other.
|Published (Last):||2 November 2006|
|PDF File Size:||3.21 Mb|
|ePub File Size:||20.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page 54 Controls the amount of dry signal to be mixed with the distorted signal. This parameter is used to increase brightness. Page 48 Dly4 Level Off, Page 18 Press the Stop button to end playback. Determines the level and width of the resonant peak at the filter cutoff point. The higher the setting, the more high frequencies are allowed to pass. Page 49 Dly4 Level Off, Do not use this product near water – for example, near a bathtub, washbowl, kitchen sink, in a wet basement, or near a swimming pool, or the like.
Density controls the amount of echo density, as opposed to the rate of increase of echo density.
LoShelf Gain Off, Sets the amount of boost or cut applied to this high frequency shelf. The built-in synthesizer is based on Fnsoniq unique Transwave technology for really unique synth sounds and life-like real instruments.
ENSONIQ ASR-X PRO User Manual
Sets the center of the low frequency EQ. Page 58 The lower the number, the asr-z the signals are damped. Page 43 Lower values will cause impulse sounds to appear as a series of discrete echoes, while higher values tend to increase the smear smoother sounding with fewer discrete echoes.
The lower the number, the more the signals are damped.
Feedback Positive settings are in-phase, negative values are out- of-phase, and impart a different tonality to the chorus. On the first and third beats, play the lowest pad, a bass drum sound. ASR-X Pro is designed for beats and loops, kit sounds are its most potent sounds. Already have an account?
Setting this parameter too high can cause the echo density to build majual a rate which exceeds the decay rate.
Ensoniq ASR-X | Vintage Synth Explorer
However it still has easy programming, excellent analog-like filters low, high and bandpassa great sampler, digital effects and easy sequencing. Comments to this Manuals Your Name.
Read all the instructions before using the product. Page 70 Sets the amount of boost or cut applied to this high frequency shelf. Don’t have an account?
We recommend settings near For less distortion, use a low gain input level and a higher output volume. This countoff can be customized or turned off. This instrument begs to have it sounds tapped into sequences in real-time or step-time so you can bring your patterns to life in seconds.
Definition 0 to Controls the rate at which echo density is increased with time. While the Fc filter cutoff parameter determines where at what frequency this peak will occur, the Q setting controls the sharpness of the peak. This is referred to as the trigger threshold. Sound parameters can be tweaked to your liking, routed through the Insert Effect or Built-in Reverb, and recorded at the Main Outputs digitally.
Mid 1 Fc 10Hz to Amp TrebGain Off, LPF Cutoff 10Hz to That should be enough to get the sort of sounds the ASR-X is intended for: Once you come up with that asr–x groove, save the sequence to disk, and load it into your computer sequencer.
Page 37 called definition. Controls the amount of dry signal to be mixed with the distorted signal. Both the Synth sounds and the Samples needed a powerful engine for playback, so we took the MR voice architecture, added resonant filters, our bit ESP-2 effects processor chip and pumped it all through pristine bit DAC’s to give you an amazing amount of “soniq” power at your ensoinq. Page 56 Q setting controls the sharpness of the peak. ADSR Attack 50us to Turn the Value knob counter-clockwise to move the level indicator as far leftward as it will go.
Kit sounds are ideal for sending waves into, since in kit sounds, each pad can have its own sound.